Seceuroglide remote control transmitter

£55.20 inc. VAT

Suits SWS Seceuroglide Seceurosmart roller garage doors

  • Frequency 433MHz
  • Four buttons (single channel)
  • Grey case
SKU: SWSSWR Categories: , Tags: , ,

Description

A garage door remote for olders SWS seceuroglide roller garage doors with an Up, Stop and Down button.

PDT grey single door keyfob to SWS Seceuroglide specification for use with a single SWS Seceuroglide roller door including RollerTec™ Compatible with grey SWS Seceuroglide control units type RF02 & RF03 or SWS RollerTec control unit types V1 – V5.

Although similar looking to the Cordula remote this will not be compatible. Use our alternative system instead.

Programming Instructions

Procedure for programming an additional transmitter to a PDT RollerTec V1 – V5 control unit. (introduced in 2005)

Grey 4-Button keyfob – Maximum 30 Transmitters

1/ Move the DIP switches on Block 1 to: 1 off, 2 off, 3 off, 4 on Wall Unit LED will flash amber
2/ Press the open button on the PCB Wall Unit LED will flash green
3/ Now press the top green button once on each new transmitter. Wall Unit LED will go solid for 2 seconds for each transmitter added
4/To exit programming mode set DIP switch 4 to OFF

Clearing transmitters from the memory (RollerTec V1 – V5)
(recommended if a handset has been lost or stolen)
1/ Isolate the power to the unit.
2/ Go to the unit on the wall and remove the cover (Take Care: Lid is attached to circuit board)
3/ Turn DIP switch 1, 2 & 3 OFF and 4 ON, wait 2 seconds. The lid-mounted signal LED will give a quick YELLOW flash.
4/ Press and hold down the stop button on the board until the following sequence has been carried out:
The flashing LED will change from flashing YELLOW to a fast flashing RED. After 10 seconds it will turn solid RED, after a further 5 seconds it will turn solid YELLOW and then after a further 2 seconds solid GREEN for 2 seconds. You must release the stop button when the LED is GREEN.
5/ To exit programming mode set DIP switch 4 to OFF

Note: the distributor code for the transmitter must match the distributor code for the receiver, if they do not match, you cannot add that particular transmitter on to the system, the LED will flash RED, GREEN then YELLOW once quickly if they are not compatible.

Procedure for programming an additional transmitter to a PDT RF03 roller door control unit

Grey 4-Button keyfob – Maximum 14 Transmitters

1/ Isolate the power to the unit.
2/ Go to the unit on the wall and remove the cover (Take Care: Lid is attached to circuit board)
3/ You will see a blue block in the top left hand corner of the board. In the block are four mini white switches.
4/ Make a note of the current position of these switches.
5/ Change the settings of the switches to 1 on, 2 off, 3 off, 4 on
6/ Turn the power to the unit back on.
7/ Take the key fob that needs loading on to the system. Press the top green button once, the light on the front of the unit will flash once.

8/ Repeat step 7 for any other key fobs that need adding to the system.
9/ Isolate the power to the unit.
10/ Reset the dipswitches to their original setting
11/ Turn the power back on to the unit.

Clearing transmitters from the memory on a PDT RF03 roller door control unit
(recommended if a handset has been lost or stolen)
1/ Isolate the power to the unit.
2/ Go to the unit on the wall and remove the cover (Take Care: Lid is attached to circuit board)
3/ You will see a blue block in the top left hand corner of the board. In the block are four mini white switches.
4/ Make a note of the current position of these switches.
5/ Change the settings of the switches to 1 off, 2 on, 3 off, 4 off
6/ Power up the unit for 10 seconds
7/ Reset the dipswitches to their original setting
8/ Turn the power back on to the unit.

Procedure for programming an additional transmitter to a PDT RF02 roller door control unit
Grey 4-Button keyfob – Maximum 14 Transmitters

1/ Isolate the power to the unit.
2/ Go to the unit on the wall and remove the cover (Take Care: Lid is attached to circuit board)
3/ You will see a blue block in the top left hand corner of the board. In the block are four mini white switches.
4/ Make a note of the current position of these switches.
5/ Change the settings of the switches to 1 on, 2 off, 3 off, 4 off
6/ Turn the power to the unit back on.
7/ Take the key fob that needs loading on to the system. Press the top green button once, the light on the front of the unit will flash once.
8/ Repeat step 7 with any other key fobs that need adding to the system.
9/ Isolate the power to the unit.
10/ Reset the dipswitches to their original setting
11/ Turn the power back on to the unit.

Clearing transmitters from the PDT RF02 memory (recommended if a handset has been lost or stolen).
1/ Isolate the power to the unit.
2/ Go to the unit on the wall and remove the cover (Take Care: Lid is attached to circuit board)
3/ You will see a blue block in the top left hand corner of the board. In the block are four mini white switches.
4/ Make a note of the current position of these switches.
5/ Change the settings of the switches to 1 off, 2 on, 3 off, 4 on
6/ Power up the unit for 10 seconds
7/ Reset the dipswitches to their original setting
8/ Turn the power back on to the unit.

Additional information

Brand

SWS, Seceuroglide

Reviews

There are no reviews yet.

Be the first to review “Seceuroglide remote control transmitter”

Your email address will not be published.